Writers' Community!
Home Page Two Columnists Q&A Submit an Article FAQs Contact Author Login
Article Submission
We Need YOUR Articles!
We'll Promote Them for FREE!

Author Login

New Authors
Register Here


Now Serving 7,757 Authors
70,409 Quality Articles
& 3,080 Current Users Online!
Featured Authors
Fran Larson (2,271)
Joel Hendon (16,285)
Shari Vaudo (418)
David Tanguay (9,577)
Michael Ramzy (633)
Missing Link (766)
E. Raymond Rock (3,068)
Gregory Lewis (1,603)
Nancy Daniels (1,550)
Mark Parsec (15,056)
Sandra E. Graham (7,883)
David Pekrul (3,696)
Ira Coffin (6,669)
Julian Price (3,951)

View All Featured Authors
Most Recent
Finding The Right MCSA Course Uncovered

Where To Do Your Adobe Web Design Course Clarified

Microsoft SQL Computer Training Companies Described

Considering Cisco CCNA Retraining Insights

Home Based MCSE Training Explained

Adobe CS4 Design Training Around The UK - Thoughts

CompTIA Network Plus Support Training - Update

Careers Training for Adobe Web Design Insights

CompTIA A Plus Retraining Courses Revealed

Programming Careers Courses Examined

Home » Categories » Computers & Networking » Technical Certification » Cisco CCNP / BSCI Exam Tutorial: EIGRP Route Summarization » Printer Friendly

Cisco CCNP / BSCI Exam Tutorial: EIGRP Route Summarization

Rated 4 out of 5
No Reader Ratings Available ?
Rate It  /  View Comments  /  View All Articles submitted by Chris Bryant CCIE 12933
Submitted Monday, March 27, 2006
Chris Bryant CCIE 12933 (13,765)
The Bryant Advantage
Log in to become a member of Chris Bryant CCIE 12933's Fan Club!


Summarizing routes is a vital skill to learn to pass the BSCI exam and get one step closer to earning your CCNP. The actual binary conversions are only part of the test, though! You've got to know how to correctly apply the summary routes, and that differs from one protocol to the next. In the last few CCNP / BSCI tutorials, we've looked at using the "area range" and "summary-address" commands to perform OSPF route summarization. Today, we'll take a look at summarizing routes in EIGRP.

WWe'll use the following four loopback addresses in this example:

Loopback 16, 16.16.16.16 /32 Loopback 17, 17.17.17.17 /32

Loopback 18, 18.18.18.18 /32

Loopback 19. 19.19.19.19 /32 On R1, we'll place these four addresses into EIGRP AS 100.

R1(config-if)#router eigrp 100 R1(config-router)#network 16.16.16.16 0.0.0.0

R1(config-router)#network 17.17.17.17 0.0.0.0

R1(config-router)#network 18.18.18.18 0.0.0.0

R1(config-router)#network 19.19.19.19 0.0.0.0

R3 is an EIGRP neighbor of R1, and that router's EIGRP routing table now looks like this: R3#show ip route eigrp

17.0.0.0/32 is subnetted, 1 subnets

D 17.17.17.17 [90/2297856] via 172.12.123.1, 00:00:29, Serial0

16.0.0.0/32 is subnetted, 1 subnets

D 16.16.16.16 [90/2297856] via 172.12.123.1, 00:00:36, Serial0

19.0.0.0/32 is subnetted, 1 subnets

D 19.19.19.19 [90/2297856] via 172.12.123.1, 00:00:08, Serial0

18.0.0.0/32 is subnetted, 1 subnets

D 18.18.18.18 [90/2297856] via 172.12.123.1, 00:00:22, Serial0

To perform manual route summarization, write out the network addresses in binary and then determine the point at which the addresses no longer have a bit in common. For these four addresses, it will be enough to write out the first octet in binary:

16 00010000

17 00010001

18 00010010

19 00010011

Working from left to right, the common bits are the first six bits - 000100xx. In decimal, this value is 16. The summary mask must be determined as well, and that value is derived from putting a "1" in the mask for each common bit. With the first six bits all set to one - 11111100 - the resulting mask is 252.0.0.0. The full summary address is 16.0.0.0 252.0.0.0.

In EIGRP, the summary address is actually configured on an interface, not under the routing process.

R1(config)#interface serial0

R1(config-if)#ip summary-address eigrp 100 16.0.0.0 252.0.0.0

02:39:50: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is down: summary configured

02:39:50: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is down: summary configured

02:40:16: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is up : new adjacency

02:40:17: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is up: new adjacency

There's an immediate side effect here that most books leave out. Your EIGRP adjacencies are going to come down after you configure this summary, but they should come back up quickly. The key word there is "should". If you configure EIGRP summary addresses on a production network, you may want to do this during non-peak hours. The timestamps on the above commands indicate that the adjacencies were down for about 27 seconds over the NBMA network. That's about 30 minutes in end-user time. )

Check R3's EIGRP routing table. R3#show ip route eigrp

D 16.0.0.0/6 [90/2297856] via 172.12.123.1, 00:01:46, Serial0

The four summarized routes are no longer in the routing table, and they have been replaced by the summary route shown at the bottom of the routing table. Notice the mask is /6, which is prefix notation for 248.0.0.0.

Knowing how and why to summarize routes is a valuable skill, regardless of the protocol in use. But before you take the BSCI exam on your way to the CCNP, make sure you know how to perform summarization with all of the core protocols!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.

For a FREE copy of his latest e-books, “How To Pass The CCNA" and “How To Pass The CCNP", just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Pass the CCNP exam with The Bryant Advantage!



Reprint Rights

Log in to become a member of Chris Bryant CCIE 12933's Fan Club!

No comments yet.


Was this article helpful to you? Leave a Public Comment or Question:

This Article has been viewed 2,498 times.
Article added to SearchWarp.com on 3/27/2006 12:54:09 PM.
View other articles written by Chris Bryant CCIE 12933 (13,765)


If you found this article interesting, you may want to check out:

Disclaimer:  All information on this site is provided for informational purposes only! By no means is any information presented herein intended to substitute for the advice provided to you by any health care or other professional or organization.


Today's Most Popular
Cisco CCNA Certification Exam Tutorial: Route Summarization

Cisco CCNA Certification: Static And Default Static Routes

Cisco CCENT / CCNA Certification Exam Tutorial: Logging Synchronous And Exec-Timeout Commands

Cisco CCNA Exam Tutorial: What's A Collision Domain?

Cisco Certification: The Definitive Guide To ARP, RARP, IARP, and Proxy ARP

How To Become A CCNA (Cisco Certified Network Associate)

Cisco CCNA Certification Exam Tutorial: Access List Troubleshooting

Cisco CCNA / CCNP Home Lab Tutorial: Access Server Configuration

Cisco CCNP / BSCI Exam Tutorial: EIGRP Route Summarization

Introduction To Cisco Networking: The OSI Model, Part I

Viewed from Cache. Load Time: 0.031.

Home  |  Page Two  |  FAQ's  |  Contact  |  Terms of Service  |  Article Submission Guidelines  |  Questions & Answers  |  Privacy  |  Mission / About
Copyright © 1999-2009 SearchWarp.com, All Rights Reserved - SearchWarp.com is an IcoLogic, Inc. Company