Writers' Community!
Home Page Two Columnists Q&A Submit an Article FAQs Contact Author Login
Article Submission
We Need YOUR Articles!
We'll Promote Them for FREE!

Author Login

New Authors
Register Here


Now Serving 8,189 Authors
71,887 Quality Articles
& 4,967 Current Users Online!
Featured Authors
Linda DeWitt (1,997)
Edward Rhymes (7,667)
Brianna Popsickle (2,495)
Teresa Ortiz (10,864)
Julian Price (13,927)
Stephany Springer (41,578)
Abigail Richards (9,835)
E. Raymond Rock (3,120)
Terry Mitchell (5,410)
Mark Parsec (16,584)
Nenita Wells (1,718)
Ira Coffin (12,151)
Krystal Kuehn (1,183)
Michael Ramzy (705)

View All Featured Authors
Most Recent
The Great Fireplace Grate

How to Generate Power for Your Home

How to Make Your Home Holiday-Ready Quickly and on a Budget!

House Painting - How to Have Your Paint and Beat the Smell, Too!

How Painting Your Home Can Save You Money and the Environment

Using Tarps in The Big Apple

How To Make a Glass Fan Light In a Timber Door Frame

The Contemporary Bathroom Remodel

Rear Projection Television Screen Cleaning

Budget Decorating Tips: How to Give Your Home a Designer Makeover with a Budget Price

Home » Categories » Do it Yourself (DIY) » Home Improvement » How To Finish the Joint of Timber Door Frame and Masonry Walls » Printer Friendly

How To Finish the Joint of Timber Door Frame and Masonry Walls

No Reader Ratings Available ? Rate It  /  View Comments  /  View All Articles submitted by Andrew Karundu
Submitted Thursday, October 29, 2009
Andrew Karundu (1,335)
http://www.karundu.com
Add to your Favorite Articles - Join Andrew Karundu's Fan Club


When frames are fixed on the door ways, a joint is formed in between the timber and masonry. This joint should be covered since timber and masonry do not bond. In buildings, different materials fixed together have joints that require to be covered. In expansion and contraction of different materials a gap will appear. Materials like glass and timber, glass and concrete, aluminum and masonry, glass and steel do not bond and thus a finish is applied on the joints.

When fixing door frames in a building, the passage should allow for a finish to cover the material joints. The design should be at least four feet. This will allow a nibs of four inches to be built on both sides of the door way. The frame is fixed in the remaining distance between the nibs. The door frame may be fixed flush on one side of the nibs. The other side may be recessed at least two inches from the nib ends. Alternatively it is fixed midway on the nibs, thus its recessed on both sides.

The finish to timber and masonry door frames uses architraves and quadrants. The architrave is used on the side where the door frame is fixed flush with the nibs. The quadrant is used where the frame is recessed into the nibs. The quadrant is a quarter round piece of timber. It is about three quarters of an inch thick. It is fixed at the ninety degree corner of the frame and the masonry. The architrave is flat with designs engraved on it. It is about one and a three quarters of an inch wide.

Once the door frame joint is ready for covering, the pieces of timber for finishing are measured. This are measured from the height above the floor skirting. Panel pins are used for nailing the architrave or quadrant onto the timber frame. The architrave is nailed at least one inch of the door frame. This is to allow adequate cover of the joint while exposing the frame. The quadrant is nailed right into the joint. These timber finishes are then painted or varnished for good aesthetics.

Andrew Karundu Is A Building Economist, Providing Home Based Solutions To Fixing, Repairing, Remodeling And Redesigning Homes. He Uses Simple Tried And Tested Methods To Improve Family Lifestyles.Visit His Site Here For Adequate Information On Most HOME IMPROVEMENT SOLUTIONS .





tweet this!



Reprint Rights

Join Andrew Karundu's Fan Club

No comments yet.


Was this article helpful to you? Leave a Public Comment or Question:

This Article has been viewed 8 times.
Article added to SearchWarp.com on 10/29/2009 3:15:36 PM.
View other articles written by Andrew Karundu (1,335)


If you found this article interesting, you may want to check out:

Disclaimer:  All information on this site is provided for informational purposes only! By no means is any information presented herein intended to substitute for the advice provided to you by any health care or other professional or organization.


Today's Most Popular
Secrets to Make Your Dishwasher Clean Perfectly

How To Waterproof An Upper Level Deck To Make a Dry Storage Area Underneath

Tips for above Ground Swimming Pool Liner Preparation and Installation!

Unlocking Your Dungeon: How to Finish a Basement Without Finishing off Your Checkbook

How To Wire a 3-Way Light Switch

Tile Shower Pan--3 Different Types

Vinyl Exterior Shutters - Choosing the Color for your Home

Covering Wood Window Trim

Swivel Sweeper Warning: Do Not Buy Swivel Sweeper until You Read This!

Self-Install a Sump Pump

Viewed from Cache. Load Time: 0.016.

Home  |  Page Two  |  FAQ's  |  Contact  |  Terms of Service  |  Article Submission Guidelines  |  Questions & Answers  |  Privacy  |  Mission / About
Copyright © 1999-2009 SearchWarp.com, All Rights Reserved - SearchWarp.com is an IcoLogic, Inc. Company